Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Temple City
If your driveway gate is sagging, binding, or refusing to close, the problem usually comes down to a failed part or a broken weld, and in Temple City it is rarely just the part. Most gates here were added to 1950s and 1960s ranch homes long after the original build, which means the hardware was retrofitted onto posts that were never designed for it. Our Gate Parts & Welding crew works on Temple City driveways every week, and we know exactly which welds hold and which posts need to go deeper. Call (747) 277-8422 for a square written price before any work begins.
We are Ironworks Gate Co., run by Victor Salinas. We have been doing gate work for over 42 years, and a live person answers our phone 24/7.
Why Ironworks Gate Co. Is Temple City’s Preferred Gate Parts & Welding Company
Gate Installation in Temple City is our specialty because we fix the cause, not just the symptom. A generalist might swap a hinge and call it done. We know that on most Temple City properties the hinge was the symptom, and the post footing was the real failure. That local knowledge comes from dozens of jobs on 91780 streets, not from a playbook written for somewhere else.
Every Ironworks technician is background-checked and uniformed. We treat your driveway the way we would treat our own mother’s. And when we finish, you get the 90-Day Done Right Promise in writing, no paperwork, no arguing. If something is not right, we come back and make it right. That is the Keystone Standard on every single job, including a simple rail repair.
We train on nine major automation brands, including Viking, DoorKing, and Linear, so if your gate has a motor attached to it, we can diagnose the whole system for Temple City Gate Motor & Opener issues, not just the steel.
Our Gate Parts & Welding Services in Temple City
Our Temple City work splits between four main services, and we see all four every week across the 91780 zip code.
Hinge Replacement
On Temple City’s post-war ranch homes, most gates were retrofitted in the 1990s and 2000s. The hinge posts were often set in shallow, non-engineered footings that were fine for a decorative gate but were never meant to carry a heavy ornamental iron panel for twenty-five years. When we replace hinges, we inspect the post first. If the footing has shifted, new hinges alone will not fix the sag.
Post Replacement
This is the most common structural repair we perform in Temple City. A gate post that wobbles or leans is usually the result of a footing that was too shallow from the start. We cut out the old post, pour a new reinforced footing to 30 inches or deeper depending on the panel weight and soil, then set and weld the replacement post. The gate hangs true again, and it stays that way.
Rail Repair
Bottom rails on swing gates corrode first, especially on Temple City properties where hard San Gabriel Basin groundwater has been splashing against the steel for decades. We cut out the rusted section, weld in new square or round stock to match the existing profile, and prime and paint the repair so it disappears into the original work.
Custom Welding
Sometimes a gate has cracked at a stress point, or a homeowner wants a mount fabricated for a new opener arm, or a lattice section needs to be rebuilt after a car kiss. Our welding is done on site with portable MIG equipment, and we work in steel, iron, and aluminum. Victor Salinas has been running Ironworks for over four decades, and our welds are the reason our customers never call anyone else.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Temple City
Most automatic gates in Temple City run on a handful of opener brands, and we are factory-trained on all of them: Viking, DoorKing, Linear, plus LiftMaster, FAAC, BFT, Ghost Controls, Elite, and Mighty Mule. If your gate has a keypad, loop detector, or remote receiver attached to it, we also handle Gate Access Control - Temple City service. Because we carry common parts and hardware on the truck, a hinge replacement or weld repair on a Temple City driveway is usually finished in one visit.
Common Gate Parts & Welding Problems We See in Temple City Homes
- Hinge posts pulling out of shallow footings. The 1990s and 2000s retrofit boom across Temple City means thousands of gate posts were set with whatever concrete was on hand. Twenty-five years of daily cycling and hard-water mineral buildup later, the post leans and the gate drops at the latch.
- Roller and track scale from hard groundwater. Temple City draws from the San Gabriel Basin, and that water is hard. Slide gates that cycle daily build mineral deposits on the rollers and rack track, which causes grinding and eventually jumped teeth.
- Phantom open/close cycles from severed loop wires. Many late-1990s automatic gates in Temple City used loop detectors buried in the concrete driveway. As those 1960s-era slabs settle and crack, the buried wire severs, and the gate opens or closes on its own. The opener is fine, and the fix is loop replacement or a wireless sensor retrofit.
- UV-baked paint and powder coat failure. The San Gabriel Valley’s summer heat and intense UV index blister and peel paint on iron gates faster than in coastal LA. Once the coating fails, corrosion reaches the steel, and that is when hinge pins seize and rails rust through.
Why Temple City’s Retrofit Gate Hardware Fails at the Post, Not the Panel
Temple City is dominated by post-WWII ranch homes built between the 1950s and 1970s. Almost none of them were built with driveway gates, and none were engineered for them. The gates that now front so many homes along Las Tunas Drive and streets branching off Rosemead Boulevard were owner-installed upgrades, mostly added in the 1990s and 2000s. What that means for a homeowner in 2026 is that the hardware is now hitting its 20 to 25 year replacement window all at once.
The cultural preference for enclosed properties among Temple City’s East Asian homeowner community, now the majority of residents, drove an unusually high density of ornamental iron gates and perimeter enclosures compared to neighboring San Gabriel Valley suburbs. Those gates are beautiful, but they are heavy, and they were often hung on posts set in footings that were too shallow for the load. A hinge replacement here almost always involves pouring a new post footing, not just swapping hardware. That is the Temple City reality we work with every week.
On a 91780 street in Temple City, our crew was called for a swing gate that had dropped 4 inches at the latch. The 1998 retrofit had a hinge post set in a shallow 18-inch footing that had cracked from hard-water mineral buildup and decades of daily cycling. We cut out the old post, poured a 30-inch reinforced footing, and replaced the hinges with stainless steel. The gate has not sagged since.
What Actually Lasts on a Temple City Gate
When we weld or replace hardware in Temple City, we spec for the conditions. That means stainless steel hinge pins and fixings instead of zinc-plated, which the hard water attacks faster. It means galvanized steel inside the post before the post is set. It means a primer and topcoat system that can take triple-digit summers without blistering. A painted steel gate that is properly prepped and coated will outlast a powder-coated gate that was never meant for this UV load. We do not guess. We know what survives here.
Pricing for Gate Parts & Welding in Temple City, CA
Every Temple City job gets a written price before we start. Hinge replacement on a standard single swing gate typically runs $200 to $450, depending on whether the post footing needs attention. Post replacement, including demolition, new footing, and welding, runs $600 to $1,200 per post. Rail repair runs $150 to $350 per rail section. Custom welding is quoted by the job, but most residential repair welds fall between $120 and $300. If we find the post needs a new footing, we will show you the issue and quote the full fix before any cutting starts. You will never get a surprise invoice.
Standing offers: $50 off any repair over $250. A free second opinion on any written estimate. An $89 seasonal tune-up. And a permanent 5% discount for seniors and veterans. Call (747) 277-8422 and we will walk the gate with you.
We Also Serve Cities Near Temple City
Our crews cover Gate Parts & Welding in Temple City and the surrounding San Gabriel Valley, including San Gabriel, Rosemead, South El Monte, and San Marino. If you are just outside the 91780 zip, call anyway. Dispatch coordinates from the Los Angeles office, and our techs are local to this corridor every day.
Serving Temple City, CA - Our Local Coverage Area
We’re based in the Temple City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Temple City
Because the hinge was never the root problem. On most Temple City retrofit gates, the hinge post is set in a shallow footing from the 1990s or 2000s, and that footing has cracked or shifted. Replacing the hinge only transfers the load back onto a failed post. The correct repair is a new reinforced footing, and we will tell you that before we start, not after the sag returns. Call (747) 277-8422 and let us look at the post.
Yes, in most cases. We weld on site with portable MIG equipment, so the gate stays on its hinges. If the crack is at a high-stress point, we may recommend a reinforcement gusset or a post inspection, but a straight weld repair on cracked ironwork is usually done in one visit.
Partially. The San Gabriel Valley’s afternoon heat expands the steel track and the gate frame, which makes a marginal clearance tighter. But the bigger factor in Temple City is hard-water scale from San Gabriel Basin groundwater, which builds up on the rollers and rack track. That scale, plus the heat expansion, is what makes the gate grind. We clean the track, replace worn rollers, and adjust the clearance. Call for a free estimate.
Usually not. On Temple City homes built in the 1960s and gated in the late 1990s, this is most often a severed loop-detector wire in the concrete driveway. The slab settles and cracks the wire, and the opener reads a phantom signal. The opener itself is often fine. We replace the loop or retrofit a wireless sensor, which is far cheaper than a new operator. Call us before you buy a new motor.
Yes. We fabricate and weld stainless steel hinges for painted iron gates in Temple City regularly. Stainless holds up better against the hard groundwater and UV exposure here, and we match the paint so the repair blends into the original panel. The hinge and the weld are covered by our written 90-Day Done Right Promise.
Call Ironworks Gate Co. for Gate Parts & Welding in Temple City
If your gate is sagging, binding, or cracked, do not wait for the post to fail completely. A dropped gate on a Temple City driveway is a security problem and a liability. Call (747) 277-8422 and a live person will answer, day or night. We will schedule a visit, walk the gate with you, and hand you a written price before any work starts. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Temple City and the San Gabriel Valley.